Product: EQUO Remover PO4 & SIO2 100gr - Resin for the elimination of phosphates and silicates
Resin for the elimination of phosphates and silicates
Phosphorous (P) is an element which is present in aquariums in various forms, but mainly as a botanical phosphate, which constitutes a primary source of nutrition for algae. High concentrations of phosphates, in particular, intervene positively on the metabolism of green algae, while brown algae proliferate with high concentrations of silicates. Besides producing the undesired effect of aiding the proliferation of algae, high levels of phosphate can inhibit the calcification process in coral and other invertebrates.
The possible causes of the increase in phosphate in an aquarium are various, including the decomposition of dead organisms or vegetation, the decomposition of uneaten food, impurities in the original water or the chemical additives used. The reduction in these phosphates (and secondly the silicates) is therefore a fundamental operation for the correct maintenance of an aquarium. In most cases, the concentration of phosphates are recommended at 0.05 ppm in order to keep the aquarium free of infesting algae. Lower values, namely 0.01 ppm are necessary for marine and barrier aquariums, in order to allow the correct growth of hard coral.
.The best method of lowering the phosphate and silicate concentration is the treatment of the water with a specific product; REMOVER PO4 & SiO2 is made up of Aluminium oxide, in a form and dimension optimized to increase the efficiency of phosphate removal. Aluminium oxide acts with a powerful absorption, forming stable complexes of phosphate and silicate molecules on its surface. With respect to other products with a different chemical formulation, REMOVER PO4 & SiO2 has some obvious advantages; The reduction in phosphate levels usually treated with aluminium oxide is far more rapid and effective than calcium hydroxide solutions. Compared to iron hydroxide, the effectiveness in absorption of Aluminium oxide is comparable, and fully sufficient in aquarium use, whereas the value for money is, however, totally in favour of aluminium oxide
Regarding aluminium oxide, it is important to underline that this product is highly insoluble in water and its use does not allow the release of soluble aluminium or other elements which could have negative effects on the inhabitants in the aquarium; in-depth scientific studies show that no traceable aluminium is released, neither are there undesired effects even after repeated use of up to 3 times more aluminium oxide than the advised dosage. Another aspect which makes REMOVER PO4 & SiO2 particularly effective in the removal of phosphates and silicates is its peculiar morphological and dimensional characteristics. REMOVER PO4 & SiO2 is, in fact, in the form of porous slivers, obtained from the chipping of aluminium oxide spheres. This allows a great increase of the surface/volume ratio (up to 300 m2/g), even thanks to the fact that the inside of the spheres are even more porous than the external surface, creating a vast increase in absorption.
-Effective decrease in phosphates and silicates thanks to the granular-metric characteristic studied for this purpose
-Prevents the growth of undesired algae
-Prevents possible deterioration of the corals due to the inhibition of the calcification process by the phosphates
- Does not alter pH
- Does not release soluble components of aluminium or other toxic substances.
Activated granular aluminium (Al2O3 > 90%)
100 g of the product are sufficient for 100 – 200 litres of freshwater or seawater;
250 g of the product are sufficient for 250 – 500 litres of freshwater or seawater;
500 g of the product are sufficient for 500 – 1000 litres of freshwater or seawater;
1Kg of the product are sufficient for 1000 – 2000 litres of freshwater or seawater;
considering an initial Phosphate concentration of about 1mg/l (ppm). Once the concentration of the phosphates are optimal (0.01-0.02 ppm, typically after one week’s treatment with REMOVER PO4 & SiO2 ), substitute the resin and insert a new load so that even the silicates can be removed. The silicates, in fact are absorbed by REMOVER PO4 & SiO2 only when the water does not contain high levels of phosphates. At this point, replace the resin only when you notice that there is an elevated concentration of phosphates.
.INSTRUCTIONS FOR USE
Insert REMOVER PO4 & SiO2 in its net and rinse with reverse-osmosis water to eliminate residues and dust (the product may liberate plenty of heat the first time it comes into contact with water: use protective gloves and/or place the product in a container or cup for the first rinse).
After which place this net in the filter or Sump, ensuring that there is a strong water flow. It is even more effective if used in a filter with fluid bed or in a phosphate reactor.
REMOVER PO4 & SiO2 , as all absorbent material, is characterized by an maximum absorption capacity and must, therefore, be changed regularly if the phosphate level remains unaltered or lowers very gradually. For this reason it is important to test the phosphate concentration level in the aquarium regularly. Aluminium oxide and Iron hydroxide cannot be regenerated in any way, as phosphates and silicates are removed from the water through the formation of stable complexes on the surface. Therefore, REMOVER PO4 & SiO2 , once used, cannot be re-utilized.